|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
HA17L431/HA17L431A Series High-Precision Variable Shunt Regulators ADE-204-029D (Z) Rev.4 Dec. 2000 Description The HA17L431LP(MPAK-5) / P(TO-92) / UP(UPAK) and the HA17L431ALP(MPAK-5) / AP(TO-92) are temperature-compensated variable shunt regulators. These ICs can operate at about half voltage in comparison with HA17431V series. They can be replaced for simple Zener diode and they can also be used for switching power supply secondary-side error amplification circuit. MPAK-5, TO-92 and UPAK packages are available. The MPAK-5 package, in particular, is suitable for high-density mounting, with a mounting area approximately half that of Hitachi's UPAK products. 4.5 mm A Mounting area reduced by approx 50% NC NC REF A UPAK K MPAK-5 K 2.9 mm REF 2.5 mm 1.6 mm Features * On-chip high-precision reference voltage source : 1.240 V 1.0% (Ta = 25C) [HA17L431A] : 1.240 V 1.5% (Ta = 25C) [HA17L431] * Small reference voltage temperature coefficient: 30 ppm/C Typ * Maximum cathode voltage: 16 V * Maximum cathode current: 50 mA * Minimum cathode current: 200 A Typ * Operating temperature range: -20 to +85C Application Example * Reference voltage generation circuits, etc. HA17L431/HA17L431A Series Block Diagram K REF 1.240 V + - A Application Circuit Example Switching Power Supply Secondary-Side Error Amplification Circuit Vout R + - K A REF R2 GND R1 HA17L431/HA17L431A Product Lineup Reference Voltage Normal Version 1.5% 1.222 to 1.258 V 1.240V HA17L431LP HA17L431ALP HA17L431P HA17L431AP HA17L431UP HA17L432UP UPAK TO-92 A Version 1.0% 1.227 to 1.253 V 1.240V Operating Temperature Range -20 to +85C Item Industrial use Package MPAK-5 2 HA17L431/HA17L431A Series Pin Arrangement HA17L431P/ HA17L431AP Marking side HA17L431LP/ HA17L431ALP A REF Marking side 1 REF A TO-92 K REF 2 A UPAK 3 K Marking side 1 K 2 A UPAK 3 REF 1 2 3 HA17L431UP HA17L432UP 5 4 Marking side 1 2 3 NC NC MPAK-5 K 3 HA17L431/HA17L431A Series Absolute Maximum Ratings (Ta = 25C) Rated Value Item Cathode voltage Continuous cathode current Reference input current Power dissipation Operating temperature Storage temperature Symbol VKA IK Iref PT Topr Tstg HA17L431LP/ HA17L431ALP 16 -30 to +50 -0.05 to +5 150 -20 to +85 -55 to +150 HA17L431P/ HA17L431AP 16 -30 to +50 -0.05 to +5 500 -20 to +85 -55 to +150 HA17L431UP/ HA17L432UP 16 -30 to +50 -0.05 to +5 800 -20 to +85 -55 to +150 Unit V mA mA mW C C 2 Note 1 Notes: 1. The anode pin is used as the reference for voltage values. 2. These values apply when Ta 25C. If Ta 25C, derate by below figure. Power dissipation PT (W) Power dissipation PT (W) 0.6 0.5 0.4 0.3 0.26 0.5W -4mW/C (1) 1.2 1.0 0.8 0.6 0.416 0.8W -6.4mW/C (1) 0.2 0.078 0.15W -1.2mW/C (2) 0.4 0.2 -3.08mW/C 0.385W (2) 0.1 -20 0 25 50 75 85 150 Ambient temperature Ta (C) (1): HA17L431P/AP (2): HA17L431LP/ALP -20 0 25 50 75 85 150 Ambient temperature Ta (C) HA17L431UP/432UP (1): With 15mm x 25mm x 0.7mm alumina ceramic board (2): Without printed circuit board 4 HA17L431/HA17L431A Series Electrical Characteristics (Ta = 25C, IK = 10 mA) Item Reference voltage Symbol Vref Min 1.222 1.227 Reference voltage deviation Reference voltage temperature coefficient Reference voltage regulation Reference input current Reference current temperature deviation Minimum cathode current Off cathode current Dynamic impedance Vref(dev) Vref/Ta Typ 1.240 1.240 5 30 Max 1.258 1.253 mV ppm/C VKA = Vref, Ta = -20C to +85C VKA = Vref, 0C to 50C gradient VKA = Vref to 16V R1 = 10 k, R2 = R1 = 10 k, R2 = , Ta = -20C to +85C VKA = Vref VKA = 16 V, Vref = 0 V VKA = Vref, I K = 1 mA to 50 mA *2 Unit V Test Condition VKA = Vref Remark HA17L431 HA17L431A *1 Vref/VKA Iref Iref(dev) 1.0 2 0.5 2.0 6 mV/V A A Imin Ioff ZKA 0.2 0.001 0.2 1.0 1.0 0.5 mA A Notes: 1. Vref(dev) = (Vref maximum value at Ta = -20C to +85C) - (Vref minimum value at Ta = -20C to +85C) Vref(dev) -20 Ta (C) +85 2. Definition of minimum cathode current. Imin is the cathode current value at which Vref = Vref(IK = 10 mA) - 15 mV. 5 HA17L431/HA17L431A Series Marking Pattern on MPAK-5 Models (HA17L431LP/HA17L431ALP) and UPAK Models (HA17L431UP/HA17L432UP) Because of the small package size, the following marking patterns are used on MPAK-5 and UPAK models. Note that the product code and marking pattern are different. The patterns are laser-marked. HA17L431LP (1) (2) (3) HA17L431ALP (1) (2) (3) HA17L431UP HA17L432UP 4 (1) D (2) 4 (1) E (2) 4 (a) L (b) (c) 4 (a) M (b) (c) Band Mark Band Mark (3) (4) (5) (3) (4) (5) Note: The boxes shown for (1) to (5) and (a) to (c) in the figure are only to indicate the position of the characters, and are not actually marked on the package. Markings * HA17L431LP, HA17L431ALP Type of Marking Meaning Model code: 4L (HA17L431LP), 4M (HA17L431ALP) (1), (2) Characters Production month code: (3) Production JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC month A B C D E F G H J K L M Code (a), (b), (c) Bar mark Production year code: Production '98 '99 2000 2001 2002 2003 2004 2005 year (a) 1 0 0 0 0 1 1 1 (b) 0 1 1 0 0 1 1 0 (c) 0 1 0 1 0 1 0 1 Notes: 1. 1 indicates a bar, and 0 indicates no bar. 2. Repeated every 8 years from 2006 on. * HA17L431UP, HA17L432UP Type of Marking Meaning Model code: 4D (HA17L431UP), 4E (HA17L432UP) Characters (1), (2) Production year code: The last digit of the year. (3) (4) Production month code: Production JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC month A B C D E F G H J K L M Code (5) HITACHI management code 6 HA17L431/HA17L431A Series Characteristic Curves Temperature Characteristics of Reference Voltage 1.260 VK = Vref IK = 10mA 1.250 K REF A 1.230 Reference Voltage Vref (V) 1.240 IK V Vref 1.220 -20 0 20 40 60 80 85 Ambient Temperature Ta (C) 50 Catode Current IK (mA) Catode Current vs. Catode Voltage2 VK = Vref 1.0 Catode Current IK (mA) Catode Current vs. Catode Voltage1 VK = Vref 0.5 0 0 0 0.5 1 1.5 2.0 2.5 Catode Voltage VK (V) 500mV/DIV -30 -5 0 Catode Voltage VK (V) 5 1V/DIV Open Loop Voltage Gain, Phase vs. Frequency Characteristics Open Loop Voltage Gain GVOL (dB) 180 50 Phase (degree) Vo 220 10F -+ Vi 4.3k 6.8k K REF A IK = 10mA 0 GVOL 0 -180 100 1k 10k 100k 1M Frequency f (Hz) 10M G = 20log Vo (dB) Vi 7 HA17L431/HA17L431A Series Noise Recovery Characteristics of HA17L431A and HA17L431 The HA17L431A bettered VKA and Vref recovery time against the HA17L431 when it was inputted noise. 12 k Vout Input pulse 1V 0V 680 VKA 7.5 k 15 V 50 ms 220 pF (External) Pulse generator (Cathode) (REF) Shunt (Anode) Regulators 0.1 F Vref 4.7 k 220 F Figure 1 Noise Response Characteristics Measurement Circuit Tek Run: 25.0MS/s Sample Trig? [T] Tek Run: 25.0MS/s Sample Trig? [T] T T Input Noise 1 1 Input Noise VKA Vref 2 2 VKA Vref Ch1 Ch3 500mV 1.00 V Ch2 1.00 V M 2.00s Ch2 2.46 V Ch1 Ch3 500mV 1.00 V Ch2 1.00 V M 2.00s Ch2 2.46 V Waveform of HA17L431A Waveform of HA17L431 Figure 2 Noise Recovery Characteristics 8 HA17L431/HA17L431A Series Package Dimension * HA17L431LP * HA17L431ALP (0.95) 1.9 0.2 (0.95) (0.6) 0.16 + 0.1 - 0.05 Unit: mm + 0.2 (0.6) 1.6 - 0.1 2.8 + 0.2 - 0.3 0 - 0.10 0.4 0.1 2.9 0.2 0.8 0.2 1.1 - 0.1 + 0.2 Hitachi Code JEDEC EIAJ Mass (reference value) MPAK-5 0.013 g * HA17L431P * HA17L431AP 4.8 0.3 3.8 0.3 Unit: mm 2.3 Max 0.5 0.1 0.7 0.60 Max 12.7 Min 5.0 0.2 0.5 1.27 2.54 Hitachi Code JEDEC EIAJ Mass (reference value) TO-92 (1) Conforms Conforms 0.25 g 9 HA17L431/HA17L431A Series * HA17L431UP * HA17L432UP Unit: mm 4.5 0.1 0.4 1.8 Max 1 1.5 0.1 0.44 Max (2.5) (1.5) 1.5 1.5 3.0 0.8 Min 0.44 Max Hitachi Code JEDEC EIAJ Weight (reference value) (0.4) 0.53 Max 0.48 Max 2.5 0.1 4.25 Max UPAK Conforms 0.050 g 10 (0.2) HA17L431/HA17L431A Series Shunt Regulator Selection Guide Package TO-92 Vref/Tolerance 2.5 V 2.2% 2.5 V 1.0% 1.24 V 1.5% 1.24 V 1.0% TO-92MOD UPAK 2.5 V 2.2% 2.5 V 2.2% 2.5 V 2.2% 1.24 V 1.5% 2.5 V 2.2% 2.5 V 2.2% 1.24 V 1.5% MPAK-5 2.5 V 1.0% 1.24 V 1.5% 1.24 V 1.0% SOP-8 2.5 V 2.2% I K max (mA) -100 to +150 -50 to +50 -30 to +50 -30 to +50 -100 to +150 -100 to +150 -100 to +150 -30 to +50 -100 to +150 -100 to +150 -30 to +50 -50 to +50 -30 to +50 -30 to +50 -100 to +150 VK max (V) 40 16 16 16 40 40 40 16 40 40 16 16 16 16 40 Topr (C) -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 -20 to +85 Product Name HA17431PNA HA17431VP HA17L431P HA17L431AP HA17431PA HA17431UA HA17431UPA HA17L431UP HA17432UA HA17432UPA HA17L432UP HA17431VLP HA17L431LP HA17L431ALP HA17431FPA 11 HA17L431/HA17L431A Series Pin Arrangement by Product Product Name (Vref / Tolerance) HA17431PA (2.5 V 2.2%) Package TO-92MOD Pin Arrangement RAK HA17431VP (2.5 V 1%) HA17431PNA (2.5 V 2.2%) HA17L431P (1.24 V 1.5%) HA17L431AP (1.24 V 1%) TO-92 RAK HA17431UA (2.5 V 2.2%) HA17431UPA (2.5 V 2.2%) HA17L431UP (1.24 V 1.5%) HA17432UA (2.5 V 2.2%) HA17432UPA (2.5 V 2.2%) HA17L432UP (1.24 V 1.5%) HA17431VLP (2.5 V 1%) UPAK R UPAK A K K MPAK-5 NC A R PS R HA17L431LP (1.24 V 1.5%) HA17L431ALP (1.24 V 1%) MPAK-5 A A K R NC NC HA17431FPA (2.5 V 2.2%) SOP-8 R NC K NC A K NC NC NC 12 HA17L431/HA17L431A Series Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi's or any third party's patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party's rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi's sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachi's sales office for any questions regarding this document or Hitachi semiconductor products. Hitachi, Ltd. Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109 URL NorthAmerica Europe Asia Japan : : : : http://semiconductor.hitachi.com/ http://www.hitachi-eu.com/hel/ecg http://sicapac.hitachi-asia.com http://www.hitachi.co.jp/Sicd/indx.htm Hitachi Asia Ltd. Hitachi Tower 16 Collyer Quay #20-00, Singapore 049318 Tel : <65>-538-6533/538-8577 Fax : <65>-538-6933/538-3877 URL : http://www.hitachi.com.sg Hitachi Asia Ltd. (Taipei Branch Office) 4/F, No. 167, Tun Hwa North Road, Hung-Kuo Building, Taipei (105), Taiwan Tel : <886>-(2)-2718-3666 Fax : <886>-(2)-2718-8180 Telex : 23222 HAS-TP URL : http://www.hitachi.com.tw Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7/F., North Tower, World Finance Centre, Harbour City, Canton Road Tsim Sha Tsui, Kowloon, Hong Kong Tel : <852>-(2)-735-9218 Fax : <852>-(2)-730-0281 URL : http://www.hitachi.com.hk For further information write to: Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223 Hitachi Europe GmbH Electronic Components Group Dornacher Strae 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00 Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 585160 Copyright (c) Hitachi, Ltd., 2000. All rights reserved. Printed in Japan. Colophon 2.0 13 |
Price & Availability of HA17L432UP |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |